|
| |
H.M.S. Communications, Inc.
IC-F3 & IC-F4
IC-F3 & IC-F4 SPECIFICATIONS
GENERAL
- Frequency coverage (Varies according to version) (Mhz)
| IC-F3 |
136.000 -150.000
146.000 - 174.000 |
| |
|
| IC-F4 |
400.000 - 430.000
440.000 - 470.000 |
- Mode: 16KOF3E (25 kHz type) 8KOF3E (12.5 kHz type)
- Number of channels: 32 (16 channels x 2 banks)
- Power supply requirement: 9.6 V DC (negative ground)
- Current drain
| Tx |
High Power |
2.0 A |
| |
Low power |
1.0 A |
| Rx |
Rated audio |
300 mA |
| |
Standby |
60 mA |
- Frequency stability:
- ± 0.0005% (EIA)
- ± 1500 Hz (ETS/CEPT)
- Usable temperature range:
- +14°F to +140°F (EIA)
- -10°C to +55°C (ETS/CEPT)
- Dimensions (proj. not included):
- 57(W) x 140(H) x 37(D) mm
- 2(W) x 5(H) x 1 15/32 (D) in
- Weight (with antenna and battery): 390 g (13.8 oz)
Transmitter
- Output power: (at 9.6 V DC)
| IC-F3 |
5 W or 1 W |
| IC-F4 |
4 W or 1 W |
- Modulation system: Variable reactance frequency modulation
- Max. frequency deviation:
- +/- 5.0 kHz (25 kHz type)
- +/- 2.5 kHz (12.5 kHz type)
- Spurious emissions:
70 dB typical (EIA)
- 0.25 MW (ETS/CEPT)
- Adjacent channel power:
- 70 dB (25 kHz type)
- 60 dB (12.5 kHz type)
- External mic. connector:
- 3-conductor 2.5 (d) mm
- (1/10")/2 k ohms
Measurements made in accordance with EIA/TIA-152-C, 204D, 603 or
ETS-300-086 or CEPT T/R 24.
Receiver
- Receive system: Double-conversion superheterodyne
- Intermed. freq. (F3/F4)
| 1st |
31.05/46.35 MHz |
| 2nd |
450 kHz |
- Sensitivity (typ.; F3/F4)
| for 12 dB SINAD |
0.25/0.3 µV |
| EMF: for 20 dB SINAD |
0.63/0.79 µV |
- Squelch sensitivity (typ.; F3/F4) : 0.25/0.3 mV (at threshold)
- Adjacent channel selectivity: 70 dB (25 kHz type) 60dB (12.5 kHz type)
- Spurious response rejection: 70 dB
- Intermodulation rejection: 65 dB
- Audio output power (at 9.6 V DC): 300 mW (typical at5% distortion with an
8 ohm load)
- External speaker connector: 3-conductor 3.5 (d) mm (1/8")/8 ohm
All stated specifications are subject to change without notice or
obligation.
OPTIONS
- BC-110A/D/V WALL CHARGER
Regularly charges the connected battery pack.
- BC-119 DESKTOP CHARGER + AD-81 CHARGER
ADAPTER
For rapid charging of battery packs. An AC adapter is supplied with the
charger. Charging time: 1 to 1.5 hrs.
- BC-121 MULTI-CHARGER + AD-81 CHARGER
ADAPTER
For rapid charging up to 6 battery packs simultaneously. An AC adapter may
be supplied depending on version. Six AD-81Ìs are necessary. Charging time:
1 to 1.5 hrs.
- BP-194 BATTERY CASE
Battery case for AA(R6) x 8 batteries.
- BP-195/BP-196 BATTERY PACKS
BP-195: 9.6 V/700mAh; BP-196: 9.6 V/1050 mAh
- HM-46 SPEAKER-MICROPHONE
Slim dimensions. Equipped with an earphone jack and a transmit indicator.
- HM-54 SPEAKER-MICROPHONE
For operation while conveniently hanging the transceiver from you belt, etc.
Max. input power: 5 W.
- HM-75A SPEAKER-MICROPHONE
Allows you to remotely select operating channels, etc.
- HS-51 HEADSET
For hands-free operation. Includes VOX, PTT and "one-touch" PTT
with a time-out timer.
- OPC-254L DC POWER CABLE
Allows you to charge a battery pack connected to the transceiver via a DC
power source (13.5 to 16 V DC). For charging Only the transceiver cannot be
simultaneously operated.
- OPC-474 CLONING CABLE
Used for radio-to-radio data cloning.
- SP-13 EARPHONE
Provides clear audio in noisy environments.
- UT-80 2-TONE UNIT
Provides the transceiver with 2-tone decode capability.
- UT-96 5-TONE UNIT
Provides the transceiver with 5-tone encode/decode capabilities.
The ICOM logo is a registered trademark of
ICOM, Inc. All ICOM radios significantly exceed FCC regulations limiting
spurious emissions. All stated specifications are subject to change without
notice or obligation. |
